Fisher Paykel Washer Gwl11 Error Codes
Top Forum Jump --> Do-It-Yourself Appliance Repair Help ....General Appliance Topics ....Household Electrical Problems ....Appliance Haikus ....The Kitchen Appliance Repair Forum ....The Laundry Appliance Repair Forum ....Heating, Ventilation, and Air Conditioning Manuals Attwood Manuals Yamaha Manuals Lowrance Electronics Manuals Raymarine Manuals O'Brien Manuals Show All > Top Musical Instrument Device Types Microphone Manuals Musical Instrument Manuals Electronic Keyboard Manuals DJ Equipment System Moderated by: Samurai Appliance Repair Man Search Our Sites for More Info! Note: Phase 5 can give a fault code 50 when the SmartDrive powers off while spinning. click site
Learn more You're viewing YouTube in German. Mine was burnt out. The diverter valve uses a small wax motor that has a rod that pushes and pulls the flap open to divert the water. You an simply test voltage to diverter or What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account?
Fisher And Paykel Washing Machine Error Codes
With Water level set to MEDIUM or LOW wash cycles complete normally with no errors. Press POWER to retain selection. Then yesterday it just stopped altogether. If the SmartDrive is empty of water, carry out a clutch disassembly procedure and check the spline drive. 3.
Cleaned and re-installed butstill the same problem. Unplug the machine. 2. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Fisher And Paykel 00100101 replaced and no power to valve when drain is attempted.the power to diverter valve is interrupted by SMD that is partially under L101.
Page 35 See fault 48 for service procedure. UNPLUG THE MACHINE BEFORE OPENING THE CONTROL PANEL ! Start by tipping the washer back, the drain motor is in the front right corner. You can also speak with a Fisher Paykel appliance technician in our repair forums in the link below.
Place the download pen over this LED and follow the instructions supplied with the data download programme. Fisher And Paykel Washing Machine Diagnostic Mode Washer shut off but water source is on Water is leaking... Page 40 63. (00111111) Phase 5 - Pump Comms Error The Motor Control Module has detected an internal communications problem between its main control system and the pump control system. Clean the gunk out of the pump using a small brush or compressed air if available. 7.
Fisher And Paykel Washing Machine Error Code 130
Page 49 235. (11101011) Phase 6 - Lid Lock Short Circuit Lid Lock fault, not activated when instructed to by the Motor Control Module. I installed inline
20MM fuse holders. Fisher And Paykel Washing Machine Error Codes Finding clothes stuck in the pump would indicate either overloading or not using a garment bag. Fisher And Paykel 10000010 Anmelden 118 0 Dieses Video gefällt dir nicht?
Generated Fri, 14 Oct 2016 06:29:24 GMT by s_ac5 (squid/3.5.20) http://indywebshop.com/fisher-and/fisher-paykel-washer-pump-blocked-error.php You can also speak with a Fisher Paykel appliance technician in our repair forums in the link below. The system returned: (22) Invalid argument The remote host or network may be down. Page 5: Diagnostic Mode 2 short beeps and lights up. Fisher And Paykel Smart Drive Washing Machine Fault Codes
Since doing this the machine has worked normally. Page 29 The third is that the pump is not operating due to Motor Control Module, wiring or pump failure. Thanks!
Can someone please help us out with the screeching??? navigate to this website Page 28 4 times during agitate.
I replaced the mosfets with the parts listed in this article. Fisher And Paykel 00110001 Often times debris will become lodged inside the drain pump causing the error code 37. The pump comes out by twisting it. 6.
From what I understand I need to test the fuses to see if they need to be replaced, can you tell me where the fuses are?
Current problem, with Regular wash cycle selected, Water level selected at AUTO, HIGH or HIGH/MEDIUM, wash cycle stops, displaying error code of 66. WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen... Thanks.
Where can I get a fuse for my washer control board
478089USP? Fisher And Paykel Washing Machine Error Code 37 I tried to put it into spin mode a few times to drain the water and each time it would pump for about 15-20 seconds before stopping, and after a few
Check the bridge terminal on the stator is not open circuit or burnt. To return Smartdrive to normal operation, press the POWER button. Generated Fri, 14 Oct 2016 06:29:24 GMT by s_ac5 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection http://indywebshop.com/fisher-and/fisher-paykel-ecosmart-washer-error-codes.php First call F&P in Australia who will then refer you to the local Service Rep who will dodge your calls for months and fail to respond to messages.
The controls and LEDs on the front panel will now serve different functions from the normal wash functions. Not sure what your referring to as the fuse box? It is giving you a code and telling you what the problem is within itself. Worth the trouble of fixing or shell out for new?
Mine has the same problem with a slight burning smell. I didn't have to use any tools though you made need some pliers on the clamps. She's called the company. Often times a small sock or undergarments will make it past the inner tub and down to the pump.
Is this repairable or must the board be replaced? Unit is 3 years old. Any suggestions on fixing this without calling a repairman?? Simply post your question in our Fisher Paykel Repair forum located at the top of this page and we will assist you in determine exactly what is wrong with the FP
This is what was causing the fuse to blow.
I'm about to start diagnosing my GW712 which stops at the spin cycle, it can be manually prompted to fill with water, rinse Page 27 Liquid Crystal Display. You mentioned the water pump was making bearing noises. Please try the request again.