Home > Fisher And > Fisher And Paykel Smart Drive 603 Error Codes

Fisher And Paykel Smart Drive 603 Error Codes

Contents

Action: Replace Display Module. It seems no one had been able to repair the Module and that this part is considered a throwaway by the manufacturer when faulty, to be replaced with a new one The fault code is as follows,43. (00101011) Phase 1 to 6 - OOB Switch FaultThe Motor Controller module has found that the signal returning from the out ofbalance switch indicates that Page 6: Data Download, Drain Pump Test, Water Valve Test, Restart Feature Restart Feature If a problem occurs in SmartDrive, it will attempt to correct the problem and restart. click site

Primary Source: Wiring. Page 44 132. (10000100) Phase 1 to 4 - Single Current Trip The Motor Control Module has detected excess current in the motor or electronic switches. Prior to writing, the Motor Controller has tested the 15 Volt supply and found that it is below the safety level for writing EEPROM and has reported this to the Display. But I didn’t have much time, I was under pressure by ‘management’ to get it going or get a new one…but soon!

Fisher Paykel Washing Machine Troubleshooting Codes

Wähle deine Sprache aus. Nominal resistance should be around 12.2 ohm for Phase 2,3 & Phase 4. During the repair, always double check and take a look at that plug to make sure it is off the wall before doing anything inside the machine. The controls and LEDs on the front panel will now serve different functions from the normal wash functions.

Check connections of the 12 way harness for bad contacts, corrosion etc. Action Phase 1, 2 &3: If the Motor Controller module has been changed from one size machine to another, then the size switch settings in the memory will have to be Generated Sat, 15 Oct 2016 20:12:19 GMT by s_ac15 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection Fisher And Paykel 00110001 Primary Source: Motor Control module Action: Replace Motor Control module (0101xxxx) Phase 2 to 3 – Display/ Motor Controller.

Page 10 Rinse Options – All Phases Smartdrive may be used in a large number of different installations where the water supplies can vary. After reading a number of the posts here, I disconnected the pump and hose but did not find any blockage. IW SmartDrives, Phase 5 and 6: To access Size Setting Mode, push and hold the FABRIC CARE button and then press the POWER button. Replace with a compatible part.

Check connections of the 12 way harness 2. Fisher And Paykel Washing Machine Error Code 37 Bail out the water, remove the pump cap and hood and clear the restriction. On Phase 6, the Machine Status screen displays the status of the diverter and the out of balance switch. IW Quick Reference Guide . .

Fisher And Paykel 10000010

Primary Fault: Display Module fault Action: Replace Display module (11101000) Phase 6 - COMMS Timeout 5 Sec IW only problem, either the Display or motor controller has not responded in time. Reconnecting the pressure tube to the pressure sensor while the bowl has been partly filled with water may have caused this. Fisher Paykel Washing Machine Troubleshooting Codes The rotor position sensing system is at fault here. Fisher And Paykel Washing Machine Fault Code 130 This indicates that either the motor is not connected or the Motor Controller module motor drive is faulty.

Resistance range will be between 0.7kΩ and 2.5kΩ. http://indywebshop.com/fisher-and/fisher-and-paykel-smart-drive-washing-machine-error-codes.php This seemed like a waste of natural resources and money and so I decided to take a good look at it and check it, to see if it was really faulty Page 2: Specifications, Electric Supply, Wash Motor, Water Valves SPECIFICATIONS Electric Supply Operating Voltage 220/240V AC 50Hz Maximum Current 2.8 amps Wash Motor Electronically commutated direct drive 3 Phase brushless DC Primary Fault: Lid Lock mechanism has jammed or failed. Fisher And Paykel 00100101

I removed the pump and control panel, found no blockage in the pump, so far only the failed fuse and vaporized tracks on the PCB shown below.

Had the exact same problems Action: 1) Check free rotation of the agitator and bowl by rotating by hand. Ask Your Own Australia Whitegoods Question Customer: replied3 years ago. http://indywebshop.com/fisher-and/fisher-and-paykel-smart-drive-703-error-codes.php In 2013 I replaced the display module but I hope I don't need to shell out $180 again !

On my GWL10 120V motor controller the Zener Diode D126 was broken

Page 4 Wash LED is on the size switch is not set, if the Rinse LED is on the size switch is set for a 5/5.5kg SmartDrive, if the Final Rinse Fisher And Paykel Washing Machine Diagnostic Mode See fault code 106 (01101000) Phase 2 to 6 See fault code 106 64. 65. 66. 81. - 95. 104. 105. (01101001) Phase 2 -6 - Comms Error Time Out These Primary Fault: Connector to the harness, either end could be at fault.

Action: Replace Motor Controller module. (01000001) Phase 5 and 6 - Pressure Transducer (Ptx) error frequency > 90 kHz The Motor Controller module has received signals from the water level sensor

level) (00100101) Phase 1 to 6 - Pump Blocked Error ( No change in the water While draining, the water level reading from the pressure sensor has not changed for over Tertiary Source: Motor Controller module. Re-connect all the wires, paying particular attention to the 2 ground spade connectors ... 10 Step 10: Failure troubleshooting.When you first look at the board you wonder...What could be faulty here??? Fisher Paykel Ecosmart Washer Error Codes Page 43 127. (01111111) Phase 5 - Machine Set up Error The Display Module has been fitted to the wrong model, size and or phase of SmartDrive, eg.

Liquid Crystal Display Primary Source: IW Display Module Action: Replace IW Display Module 28 – 30. (000111xx) Phase 1 – Display / Motor Controller out of Sequence Refer to fault code Action: Turn the Smartdrive off at the wall and then back on again in 5 seconds. The most likely cause is that the SmartDrive is siphoning. my review here To print the manual completely, please, download it.

Action: Replace Motor Control Module. 55. (00110111) Phase 3 to 6 - System Step Fail Primary Source: Rotor Position Sensor.