Home > Fisher And > Fisher And Paykel Pride 5.5 Error Codes

Fisher And Paykel Pride 5.5 Error Codes

Contents

Page 42 106. (01101010) Phase 2 to 3 and 5 - Display to Motor Control Module Communications Errors (Phase 6 IW Also) These faults are reported when the Display Module detects Mine was burnt out. If the drum rumbles when spun then the bearings have probably gone. This seemed like a waste of natural resources and money and so I decided to take a good look at it and check it, to see if it was really faulty click site

This process could take up to 8 minutes depending on the type of fault. Remove the 2 screws on the top rear side of the control panel. Smell and all!

1) I fixed the pump screeching noise last month

2) I checked the diverter value and it is free of clogs

Any luck? Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Australia Whitegoods How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help

Fisher Paykel Washing Machine Troubleshooting Codes

Press START/PAUSE. Get as much water out as possible (use a cup, sponges or towels) 3. user-manual-Paykel... Talked to Australia.It needs bearings, suspension rods too, plus the hot and cold valves need replaced.

Then yesterday it just stopped altogether. Hopefully that has fixed it.

I have just tried to fill my F/P machine but the water is just dripping in. so i just need to buy the switch and acuator assembly and re install, yea? Fisher And Paykel 00110001 I didn't have to use any tools though you made need some pliers on the clamps.

mw059 fisher & paykel smart drive 9 pride 5.5 Expert: Kelly replied3 years ago. Fisher And Paykel 10000010 Page 34 46. (00101110) Phase 5 IW - Display EEPROM Check The Intuitive Display has detected a problem with its internal EEPROM. you were spot on! I couldn't even get machine to start so I finally replaced it.

▶ Fisher and Paykel Washing Machine Screaching Noise Repair - YouTube

I FOUND IT.....

Mine screeches too.

Penguin45. Fisher And Paykel 00100101 Let me know what you find, please. Ask Your Own Australia Whitegoods Question Customer: replied3 years ago. Slow LED ON, OPTION (2). Press POWER to retain selection.

Fisher And Paykel 10000010

I soldered in a 100 ohm resistor in lieu of the SMD. Phase 5 Display Module cannot be fitted to a Phase 4 Motor Control Module. Fisher Paykel Washing Machine Troubleshooting Codes Which bit of "Unplug it" is causing the problem? __________________ Stop eMailing me. Fisher And Paykel Washing Machine Fault Code 130 Lid Lock Resistance range 73 ohms +/- 5 ohms Normally low voltage, potentially 230V if harness is grounded on the cabinet.

Two quick beeps will sound and the LEDs on the front panel will change. get redirected here Use the sticky at the top of the forum (you're in the Oz one now!) to do the diagnostics properly and report back. Get it. Click "Add" to insert your video. Fisher Paykel Ecosmart Washer Error Codes

Wird verarbeitet... Page 41 105. (01101001) Phase 2 to 6 - Comms Error Time Out These faults are reported when the Display Module detects an error in the communications between the Display Module Anmelden Transkript Statistik 37.598 Aufrufe 117 Dieses Video gefällt dir? navigate to this website Your cache administrator is webmaster.

the diverter valve was jammed. Fisher And Paykel Washing Machine Diagnostic Mode Cold it be the pressure of the water tank or my machine?

I have a Fisher Paykel washer have replaced the control module and now it makes a beep sound and the Any info you have would be greatly appreciated!

hi can anyone help with my fisher and paykle spin light is stuck on an t keeps beeping an wont do anything eles im

If unsure how to put it back together, just take a picture of how it looks before you start.

Page 27 Liquid Crystal Display. Unplug the machine. 2. The system returned: (22) Invalid argument The remote host or network may be down. Fisher And Paykel 00101011 The pump comes out by twisting it. 6.

Here are the possible tests to run (TEST LIST). Paykel EcoSmart... Look for the pump (it has hoses connected to it and 2 separate plug in wire points), The hoses come off easy by squeezing the spring retainer clip and the wires http://indywebshop.com/fisher-and/fisher-paykel-error-codes.php I can get to the machine later today, check and get back to you with the exact details.

You need to watch the washing machine to see when it aborts to get an idea which of the three areas to look at. Page 23 START/PAUSE then push the POWER button. View Most Popular Paykel EcoSmart GWL15 Washing Machines Related Question Error E1 for washing machine Washing Machines Open Questions: 0 Answers Why doesn't it start? user-manual-Paykel...

Then it will randomly stop screeching. Jan 08, 2013 | Fisher and Paykel Washing Machines 1 Answer Fisher and paykel 7.5 smartdrive accelerator starts with water filling the mahine in short bursts for 40 seonds then stops Page 28 4 times during agitate. Page 13 Out Of Balance Recovery Adjustment (GW and MW only) Phase 3 to5 When Smartdrive is spinning it senses if the wash load is out of balance.

Action: Replace the Display Module. Just be careful to "disconnect" the wires and not yank them out of the connections. 5. Page 15 It also displays the Size setting of the SmartDrive and the water level. The error codes from t02 will probably be the best indicator of your problem. (scroll down to bottom to see what each command button does once you are in test mode)

I hit the power button and it wouldn't even start so I finally replaced it.

Maybe you have something (like some junk) jammed in the pump thats casuing the screeching ??

There are Page 35 See fault 48 for service procedure. I seem to have the exact same issue.

I have a GW712 that was stopping at the spin cycle. Help this question get an answer by entering the correct category or product below.

Belts? How to run a diagnostic test: Unplug power cord, then wait 30 seconds. E1. There is a reconditioned board at the link below.

Jul 01, 2016 | Washing Machines 2 Answers Smart drive 051 error code 32 Hello, Have you tried unplugging it and plugging it in again?