Home > Error Code > Fc Error Codes

Fc Error Codes

Contents

Check the drive motor for powered rotations. Press START to continue the cycle from the moment that power was lost. Make sure all grounding switches are engaged. 3. Refer to the Water Temperature Sensor section. have a peek at these guys

Look for condensation or contamination on probe receptacle. Check/clean drain pump filter of foreign objects. 5. Press STOP/CANCEL to clear the display. If error continues, disconnect power and replace control.

Whirlpool Oven Error Codes

Find Parts Whirlpool Duet Front Loading Automatic Washer Fault Codes Failure Code Fault Code Description Solution FH No water detected entering machine or Pressure switch trip not detected. Press STOP/CANCEL to clear the display. Door switch open while door is locked. 1.

  1. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
  2. Note: If this error occurs, the door will remain locked and the drain pump will run constantly even if 'cancel' is selected.
  3. With this failure, power to the motor controller cannot be turned off by the machine controller.
  4. F05 - Water Temperature Sensor Error - Unplug and disconnect power to the unit and check all connections to the water temperature sensor, heating element and element relay.
  5. F1-E5 - Calibration Shifted - Disconnect power for at least 30 seconds and then reconnect.
  6. Check the drain hose and make sure it is not plugged or kinked. 2.
  7. Check the MCU by looking for operations of the drive motor. 7.
  8. compare content of files.
  9. F5 - E0 Door switches do not agree (condition exists when door switch is closed indicating an open door, and latch switch is closed indicating a locked door) 1.

Press STOP/CANCEL to clear the display. ^ top LS Lid switch error The control should flash this error code if it cannot detect the lid switch opening and closing properly. Check for stuck lock switch. Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU Ge Oven Error Codes F3 F4 or F5 Humidity sensor open or shorted Replace humidity sensor.

Sud SUDS LOCK (Overdose of detergent detected during the wash cycle) The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. Ge Oven Fault Codes Select 'cancel' and observe for one minute for errors. Check for loose connectors. 3. http://www.repairclinic.com/RepairHelp/FaultCodeLinks Door not opened during 3 consecutive cycles. 1.

Check the water temperature sensor and connection to it. 3. Whirlpool Range Error Code F9e0 Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table on page 10. F31 MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU), Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table.If resistance is 0 Ω or infi nite value, replace NTC.

Ge Oven Fault Codes

Gently pull the tab down about 1/4 inch or until a click is heard. 6. CE Communications error If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit beeps once. Whirlpool Oven Error Codes This should clear the unit of the excess detergent. 1. Ge Oven Error Codes F2 Check the drive motor for powered rotations. 6.

Check the inlet valve for proper shut off. 7. More about the author E2 - Shorted Thermistor - Replace thermistor. The resistance of both door coils (between pin 1 and 3) should be approx. 320 Ω. Check keypad connector for firm connection (keypad connects to control board). 2. Whirlpool Washing Machine Error Codes E1

Replace the pump. Press STOP/CANCEL to clear the display. For SELF CLEAN models, check door lock operation. http://indywebshop.com/error-code/fix-error-codes.php Check the drive system for any worm or failed components and reconnect power and plug unit in.

If the condition continues four times, the F31 code will show.MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will Whirlpool Top Load Washer Error Codes Check the drive motor for powered rotations. F28 SERIAL COMMUNICATION ERROR The communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. 1.

Diese Funktion ist zurzeit nicht verfügbar.

Check for drain pump failure. 6. If no damage to wires and all connectors okay, proceed to step C. Confirm water supply to steamer. 5. Whirlpool Microwave Error Codes Check harness on steamer electronic board. 2.

F30 DISPENSER SYSTEM ERROR When the dispenser motor cannot be driven to its proper position. 1. F1-E4 - Model ID Error - Disconnect power for at least 30 seconds and then reconnect. Door switch/lock unit failure. 1. http://indywebshop.com/error-code/fed-error-codes.php Check the connections between the Steamer 3.

FdL - Door Lock Error - It is possible the door lock mechanism is broken or removed, or the door switch/lock unit has failed. After disconnecting power to the unit, try scraping this coating off the pins. • Check the resistance values between the serial communications pins with the connectors in place. Check the drive motor for powered rotations. 8. This code will also appear if the user presses the START key while the lid is open.

Make sure the drain pump is free from debris or foreign objects and then reconnect power and plug unit in. Yes No Thanks! SL - Suds Lock - This error will occur if the unit detects suds but is unable to clean them out. Press STOP/CANCEL to clear the display.

Potential Causes • Door Lock Mechanism broken or removed from the Door • Check Door Lock/Switch Assembly • Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Wird geladen... Make sure the harness does not have a bad connection. • Check the quick disconnect at the motor terminal. Verify CCU operation by running a Diagnostic Test or any cycle.

This may indicate a bad pump, an extra heavy load, excessive detergent or excessive suds. Disconnect power from unit.