Home > Error Code > F7 Error Code Kitchenaid Microwave

F7 Error Code Kitchenaid Microwave

Contents

The door should now be unlocked. Turn off hot and cold water to faucets and unplug the unit before proceeding. If connections are ok, then check individual switches as outlined for the F5 error code. F2-E1 - Touch Pad Cable Unplugged - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. have a peek here

Clean the glass surface and remove all objects placed on it. 2. It is also possible that the electronic control board or console electronics has failed. View Most Popular Microwave Ovens Related Question Mod.KHMS155LSS-1 Getting F-6 Fault code ???? F05 - Water Temperature Sensor Error - Unplug and disconnect power to the unit and check connections to the water temperature sensor.

F7 E0 Error Code Kitchenaid

Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 3. Additional Questions If the microwave displays a error code F7, typically the control microcomputer board is not the failed component.  The control is the ‘messenger' of the problem, typically not the Kitchen Aid Cooktop Fault Codes Electronic Touch Ceramic 30 inch.

  • Replace failed component.
  • I'm having the same problem with my KitchenAid microwave; but I am only getting the F7 error intermittently.
  • Press and hold any key for 1 minute to clear R failure code from memory.
  • Not finding what you are looking for?
  • F14 EEPROM error The Central Control Unit (CCU) receives its data from an EEPROM onboard the CCU.
  • Click Select6.
  • Check for reversed plug connection on controls or loose wiring.22.
  • This is the metal propeller looking part, that you can see through the round transparent plastic cover/window located on the top ceiling, inside of microwave.
  • Disconnect power for 1 minute. 2.

Victor Lourenco Oct 24, 2012 When I checked the voltage at 4903-1 on relay board it was 120 Volts however when the microwave is turned on it drops to t o Check/clean drain pump filter of foreign objects. 5. F8 - Control Board Failure - Replace control board (clock). Kitchenaid Microwave Error Code F6eo I give it a time and press start, it runs for about 18 seconds, gives error code F7 and stops running.

Plug in washer or reconnect power. 4. Whirlpool Microwave F7 Error Code F21 / F22 - Central Control Unit (CCU) / Touch Pad / LED Assembly Error - Check that the touch pad/LED assembly is working by selecting different cycles and changing the Reconnect power and plug unit in. Verify there is not a siphon problem. 2.

Another low tech solution, which I haven't tried yet, would be to use a strong enough magnet on the outside of the "window", to manually turn the stirrer, to free it Kitchenaid Microwave Error Code F2e1 This should clear the unit of the excess detergent. 1. If code re-appears, replace control board (also called ERC or clock). Selecting the item displayed will insert text that looks like this: [[ASIN:B00X4WHP5EAmazon Echo]] 7.

Whirlpool Microwave F7 Error Code

Replace failed component. http://www.applianceblog.com/mainforums/threads/6458-Whirlpool-Microwave-G2-Error-code-F7 Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). F7 E0 Error Code Kitchenaid E1 Temperature sensor open E1 flashes in the numeric display when the temperature sensing circuit is open. Kitchenaid Microwave Error Code F2 H2 Possible Causes / Procedure 1.

Plug in washer or reconnect power. 5. navigate here Any help would be appreciated. Possible Causes / Procedure • If too much detergent was used: - Run the unit through a Rinse/Spin cycle. - Run a Normal cycle without adding any detergent. You can still see all customer reviews for the product. Kitchenaid Microwave Error Code F6e0

If corrections are made in any step, reconnect power to control. http://www.applianceaid.com/ Appliance Repair Aid Reply With Quote November 25th, 2006,12:33 AM #4 cmccoy11 View Profile View Forum Posts Member Join Date Nov 2006 Location SE MI Posts 3 Thanks for the If connections are not damaged, measure door switch (door open = latch open) and latch switch (unlatch = switch open) and replace either if defective. Check This Out F36 Temperature probe hardware error 1.

Check all Cavity Thermostats for closed circuit. 5. Kitchenaid Microwave Error Code F2h2 Check the door switch/lock for any debris or foreign objects. Check the pressure switch for proper operation.

F13 Dispenser circuit error If the dispenser motor is not able to be driven to its proper position.

Check CCU is also operational by performing a diagnostic test or any cycle. All for a $600.00 appliance! Plug in microwave oven or reconnect power.16. Whirlpool Microwave F7 Call For Service Check wire harness connections to the Central Control Unit (CCU) and the dispenser motor.

Note: Unit will attempt to lock itself during this error six times before displaying the error code. F06 - Drive Motor Tachometer Error (Unable to Detect Motor Speed) - Check the shipping system including shipping bolts, spacers, and cables are removed and unplug unit and disconnect power. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. http://indywebshop.com/error-code/f6-error-code-whirlpool-microwave.php If problem persists, unplug microwave oven or disconnect power.17.

Verify CCU is working by performing diagnostic test or any cycle. Possible Causes / Procedure 1. Sud Suds lock (Overdose of detergent detected during the wash cycle) The Motor Control Unit senses a suds lock condition by analyzing the current draw on the drive motor. If failure remains, disconnect power and replace control.

Keyed in 30 seconds and it turned on with a grinding sound, then turned itself off. A double oven will have two of each switch and one common wire. 1. Replace failed component. Possible Causes / Procedure 1.

Some models incorporate keypad in to control board as one unit. F10 - Motor Control Unit (MCU) Heat Kink Thermal Trip (Too Hot) - Check for proper installation and ventilation, and make sure unit is not located near a heat source. Check drain pump and pressure switch and verify CCU operation by running a diagnostic test or any cycle. Check the water temperature sensor.

Reconnect power and plug unit in. Deals and Shenanigans Yoyo.com A Happy Place To Shop For Toys Zappos Shoes & Clothing Conditions of UsePrivacy NoticeInterest-Based Ads© 1996-2016, Amazon.com, Inc. F22 - Key Sensitivity Problem - Disconnect power for one minute and check to see if error reappears once power has been restore. Posted on Mar 12, 2011 Helpful 0 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Ace Level 1: An expert who