Home > Error Code > F27 Error Whirlpool Duet

F27 Error Whirlpool Duet

Contents

Replace User Interface. Replace the Motor Control Unit. Unplug washer or disconnect power. 2. Remove the lower toe panel. 3. Source

Is this the model with a seperate steamer board? « Last Edit: January 10, 2015, 08:57:08 AM by LowSL2 » Logged LowSL215+ Years of Professional Appliance Repair ExperienceFormer $ears/a$e tech Washer Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). That was at noon today. F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle. http://forum.appliancepartspros.com/washer-repair/531392-whirlpool-error-code-f27.html

F27 Error Code Kenmore

You also want to remove the air hose from the water level switch, and blow into the hose,as hard as possible, to clear any debris. Short circuit of Heater to Ground. F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. The doorswitch may cause an interference for the powersupply of the MCU.

This is verbatim from the tech sheet. Check the electrical connections at the pump and make sure the pump is running. 4. Check for continuity of the User Interface harness. 2. Whirlpool Washer The failure will be reset after running the Diagnostic Test Program. 1.

The machine will drain for 3 minutes before unlocking the door. 3. First time? Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check Drive belt • Check MCU • Check Motor • Check Wire Harness i thought about this Check the water temperature sensor and connection to it. 3.

F13 Dispenser circuit error If the dispenser motor is not able to be driven to it’s proper position. Replace heater. Door switch open while door is locked. 1. Anmelden Transkript Statistik 140.515 Aufrufe Dieses Video gefällt dir?

Whirlpool Washing Machine Fault Codes

During the Cleaning Cycle was load detected inside the drum and Cleaning Cycle was interrupted by indicating “rL” to User. http://www.appliancehelponline.com/whirlpool.html Die Bewertungsfunktion ist nach Ausleihen des Videos verfügbar. F27 Error Code Kenmore The Steamer will no longer function for any wash cycle and should be replaced. Whirlpool 6th Sense Washing Machine Error Codes Help someone Are you good at fixing things?

Check the drive motor for powered rotations. 8. this contact form Remember to put some sort of bucket under the faucet. If the inlet valve would fail in this manner, the tub would be trying to fill with water all the time and not shut off. Sprache: Deutsch Herkunft der Inhalte: Deutschland Eingeschränkter Modus: Aus Verlauf Hilfe Wird geladen... Whirlpool Duet Dryer Error Codes

  • Unplug washer or disconnect power. 2.
  • F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle.
  • If during one wash cycle 4 undervoltages occur then a Motor Control Unit failure is displayed. 1.
  • Replace CCU board.
  • Check connection to water heater. 3.

Look for obstructions in the clean-out trap and impeller area of the pump. 4. Check wire harness connections to the User Interface and the Central Control Unit. 3. b. have a peek here c.

Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 Verify CCU operation by running a Diagnostic Test or any cycle. Check the MCU by looking for operations of the drive motor. 5.

Replace the Motor Control Unit.

Press CANCEL and observe for 1 minute to ensure operation is correct. 2. Push the door and check if it is completely closed. 2. Press PAUSE/CANCEL two times to clear the display. 1. Answers Who answers the questions?

Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 Replace heater. Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check the Drive system for any worn or failed components • Check MCU Check This Out If the error code reappears, proceed to step 2. 2.

Check harness on steamer electronic board. 2. F2 - E1 Keypad cable unplugged F2 - E5 Cancel key drive line open F2 - E6 Cancel key drive line open F3 - E0 Oven temperature sensor (RTD) opened (upper WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen... codes except F1-E3.

It should be approx. 115 Ω. 4. Potential Causes • A power glitch may cause this error. Get more answers from the people in your networks Tags Whirlpool , Washers Click to remove this tagging. Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4.

AppliancePartsPros.com is the registered trademark of AppliancePartsPros.com, Inc. Check resistance of heating element, if present on this model. (abnormal = infinity) 4. Replace User Interface if drum is rotating. 4. Plug in washer or reconnect power. 5.

F22 DOOR LOCK ERROR After 6 failed attempts to lock the door. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. Remove the clean out cover on the pump and check for debris. Check for proper installation, verify the unit is not located near a source of heat and has proper ventilation. 2.

The lid switch must be opened at least once before restarting the cycle, if this condition occurs. Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen. MAIN RELAYS ERROR One of the main relays is not working properly. Press STOP/CANCEL to clear the display.

Household Appliances, StairliftsHousehold Appliances, Steam CleanersHousehold Appliances, Steam IronsHousehold Appliances, Tumble DryersHousehold Appliances, Vacuum Cleaners Full list ... Door switch/lock unit failure. 1.