Home > Error Code > F11 Error Code Electrolux

F11 Error Code Electrolux

Contents

The part number for the EOC is 316443865 Good luck. We pulled out the oven temperature sensor. Gene // Apr 1, 2015 at 8:16 pm Hello MML, Sad news about that ribbon cable. or Is it something else that's causing this problem? http://indywebshop.com/error-code/f10-error-code-electrolux.php

ft. ... I was not aware of a door lock (because I don't see anything to slide) other than the "lock" symbol on the control panel that I've never used… Can you tell? Gene // Dec 24, 2014 at 1:10 pm Hello Craig, It is not difficult to do it but, for more accurate advice I need the complete model number of the oven. My range is possessed.

Electrolux Range F11

Thanks so much Jacqui Gene // Jan 4, 2015 at 11:59 am Hello Jacqui, My answer is Yes. Thank you Gene // Nov 5, 2014 at 11:41 pm Hello Frank, Thank you for your question. Test wiring harness and connections between PS board 2 (P2) and ESEC 30 UIB connector P7 4.

It suppose to be about 1100 Ohms. If there are some relays on it, replace the EOC. I am getting a error code "F-95 ERR". Frigidaire Oven F11 Error Code AppliancePartsPros.com Happy New year!

Sounds like the EOC is the culprit. Electrolux Oven F11 If fault returns when power is reconnected, continue the troubleshooting. You can reset your wall ... http://www.askgene.com/2013/04/14/oven-error-codes/how-to-fix-frigidaire-of-electrolux-range-or-oven-with-an-f-error-code/ Thank you.

I ran the self clean on my electrolux and within 2 weeks of using my oven again, I had the F10 runaway temperature alarm. Frigidaire Oven Error Codes I had a repairman ... Your stove is new and suppose to be covered under manufacturer warranty. Not finding what you are looking for?

Electrolux Oven F11

So the only solution is to replace the EOC. see this Denise // Jun 15, 2015 at 1:38 pm Hi, Gene, I have a PLEs39ECG, serial NF73726 that gives me an error F30. Electrolux Range F11 Thanks for your help! Electrolux F11 Beeping We will proceed further.

The part number for the sensor is 316217002.If the resistance is normal, then one of the other causes mentioned above is producing your F10 code. this contact form The code you are experiencing typically indicates a control communication error. Sounds like the EOC has gone bad again. Gene // Jul 9, 2015 at 2:26 pm Hello, Bessie. Electrolux Oven Error Codes

Saves me a trip to the store to buy the wires. See Details Whirlpool WOC95EC0AB 30 in. Include an image. have a peek here Ken Gene // Dec 26, 2014 at 1:53 pm Hello Ken, Looks like the cause of the problem is a faulty EOC.

Well, it was almost a year to the date. Electrolux Oven Error Code F14 The correction for this problem is to replace the EOC. There is a separate membrane switch in your range which would need to be replaced in such situation.

Virginia Beach, VA "Your service people are so friendly and helpful.

  • Check/reseat ribbon harness connections between TST panel and EOC. 3.
  • The cause of the problem in such situation most likely is a failed wire harness between the sensor and the EOC.
  • Press UPPER OVEN or LOWER OVEN to select oven. 2.
  • You have to click on every one of them.
  • The cause of this problem is a faulty EOC.
  • Have a manual for Electrolux Kitchen Ranges?
  • S.
  • It can be easily determined by the model number, usually located on the frame behind the bottom drawer or on the oven door frame.

Gene // Nov 21, 2013 at 3:17 pm Hello Dave. Very likely the problem is a faulty relay board. The part number for the temperature probe is 316217002 Otherwise the EOC would need to be replaced. Electrolux Oven Error Code E15 It was 1 hr into baking and the temperature did runaway, everything was black.

too much money and they are garbage. Gene // Apr 1, 2015 at 8:21 pm Hello Judy, Thank you for your good words! Keep me posted. http://indywebshop.com/error-code/eza1735i-std-return-code-27426-error-code-00002.php Disconnect the broiler igniter wires and check for continuity between each wire coming to the igniter and the chassis.

Good luck. Starts beeping then stops and starts again after a while. The clock turns on but will not allw me to adjust it and once again the broiler automatically turned on however this time the screen flassed the F11 error. Search Fixya Press enter to search.

I checked the resistance on the probe's bare wires and it reads 1099 ohms. Replace the TST panel 4. The best way to do it is to pull the range out of the wall. Also the model number you posted is incomplete.

If you need further assistance, please reply to this thread. In order to access it you would need to remove the oven from the cabinet. Gene // Apr 1, 2015 at 8:35 pm Hello Steve, Thank you for your question. This part is usually located on the back wall in the upper part of the oven cavity but it can be easy tested from the EOC.

Also the model number you sent is incomplete.